Answer:
A) equal in amount to the force your friend exerts on you.
Explanation:
According to the Newton's third law of motion every action has equal and opposite reaction. Here both the bodies exert equal and opposite forces on each other but it is just that I am able to stop myself from getting pulled by a greater force of friction by applying more normal force on the ground.
As we know that the force of friction is given as:
[tex]f=\mu.N[/tex]
where:
[tex]\rm f=\ force\ of\ friction\\N=\ applied\ normal\ force\ to\ the\ ground\\ \mu=\ coefficient\ of\ friction[/tex]
Consider a Boeing 777 flying at a standard altitude of 11 km with a cruising velocity of 935 km/h. At a point on the wing, the velocity is 280 m/s. Calculate the temperature and pressure at this point.
Answer:
ΔP = 97.93 Pa , T₂-T₁ = 71.5° C
Explanation:
For this problem let's use Bernoulli's relationship, as point 1 we will take the plane and as point 2 the air
P₁ + ½ ρ g v₁² + ρ g y₁ = P2 + ½ ρ v₂² + ρ g y₂
As the whole process occurs at the same height y₁ = y₂ = 11 km. We will consider that the air goes in the opposite direction to the plane
P₂ –P₁ = ½ ρ (v₁² - v₂²)
Let's reduce the magnitudes to the SI system
v₁ = 935 km / h (1000 m / 1 km) (1h / 3600s) = 259.72 m / s
v₂ = 280 m / s
The density of air at 11000 m is
Rho = 0.3629 kg / m
P₂-P₁ = ½ 0.3629 (259.72 + 280)
ΔP = 97.93 Pa
The variation of the temperature with the altitude is 0.65 per 100 m
T₂ –T₁ = (0.65 / 100) 1000
T₂-T₁ = 71.5° C
The temperature has decreased this value
A helium atom falls in a vacuum. The mass of a helium atom is 6.64 x10-27 kg. (a) From what height must it fall so that its translational kinetic energy at the bottom equals the average translational kinetic energy of a helium molecule at 300 K
Answer: The question is incomplete as some other details are missing. Here is the complete question ; A helium atom falls in a vacuum . The mass of a helium atom is 6.64 x 10-27 kg . (a) From what height must it fall so that its translational kinetic energy at the bottom equals the average translational kinetic energy of a helium molecule at 300 K? (b) At what temperature would the average speed of helium atoms equal the escape speed from the Earth, 1.12 x 104 m/s.
a) Height = 95.336Km
b) Temperature = 20118.87K
Explanation:
The detailed steps and calculations is shown in the attached file.
The helium atom must fall from 95.336 km to achieve average translational kinetic energy at 300 K.
What is Translational kinetic energy?It is the required energy to accelerate the particle or object from the rest to achieve the given velocity.
The height can be calculated by the formula,
[tex]h = \dfrac 23 \times \dfrac {kt}{mg}[/tex]
Where
h - height =?
k - constant =[tex]1.38\times 10^{-23}[/tex] J/k
t - temperature = 300 k
m - mass
g - gravitational acceleration = 9.8 m/s^2
Put the values in the formula,
[tex]h = \dfrac 23 \times \dfrac {1.38\times 10^{-23}\times 300 }{6.64 \times 10^{-27}\times 9.8}\\\\h = 95335.4 {\rm\ m \ \ or}\\\\h = 95.336\rm \ km[/tex]
Therefore, the helium atom must fall from 95.336 km to achieve average translational kinetic energy at 300 K.
Learn more about translational kinetic energy:
https://brainly.com/question/25612167
When a crown of mass 14.7kg is completely submerged in water, an accurate scale reading reads only 13.4kg. Is the crown made of gold?
Answer:
No. The crown is made of lead
Explanation:
From Archimedes principle,
D/D' = W/U
Where D = density of the crown, D' = Density of water, W = weight of the crown in air, U = Upthrust of the crown in water.
make D the subject of the equation,
D = D'(W/U)................... Equation 1
W = mg
Where g = 9.8 m/s², m = 14.7 kg.
W = 14.7(9.8) = 144.06 N.
U = 9.8(14.7-13.4) = 12.74 N.
Constant: D' = 1000 kg/m³
Substitute into equation 1
D = 1000(144.06/12.74)
D = 11307.69 kg/m³
Density of the crown = 11307.69 kg/m³
And Density of Gold = 19300 kg/m³
From the above, The crown is not made of Gold
To determine if the crown is made of gold, we need to use Archimedes' principle and calculate its density. If the density is greater than the density of water, the crown is made of gold.
When a crown of mass 14.7kg is completely submerged in water, an accurate scale reading reads only 13.4kg. To determine if the crown is made of gold, we need to use Archimedes' principle. According to this principle, when an object is submerged in a fluid, it experiences an upward buoyant force equal to the weight of the fluid displaced by the object.
If the crown is made of gold, its density should be equal to or greater than the density of water. We can calculate the density of the crown by dividing its mass by the volume of water it displaces. If the density of the crown is greater than the density of water (1kg/L), then the crown is made of gold.
In this case, the mass of the crown is 14.7kg, and the mass of the water displaced is 13.4kg (since the scale reading is lower). By using the equation density = mass/volume, we can calculate the volume of water displaced by the crown and determine its density.
Learn more about crown is made of gold here:
https://brainly.com/question/34135658
#SPJ3
A car sits on an entrance ramp to a freeway, waiting for a break in the traffic. Then the driver accelerates with constant acceleration along the ramp and onto the freeway. The car starts from rest, moves in a straight line, and has a speed of 20 m/s (45 mi/h) when it reaches the end of the 120-m-long ramp. (a) What is the acceleration of the car? (b) How much time does it take the car to travel the length of the ramp? (c) The traffic on the freeway is moving at a constant speed of 20 m/s. What distance does the traffic travel while the car is moving the length of the ramp?
The acceleration of the car is 1.67 m/s². It takes approximately 11.23 seconds for the car to travel the length of the ramp. The traffic travels approximately 224.6 meters while the car is moving the length of the ramp.
Explanation:(a) To find the acceleration of the car, we can use the equation:
v² = u² + 2as
Where v is the final velocity (20 m/s), u is the initial velocity (0 m/s), a is the acceleration, and s is the displacement (120 m).
Plugging in the values, we have:
20² = 0² + 2a(120)
Simplifying the equation, we get:
a = (20²)/(2 * 120)
Therefore, the acceleration of the car is approximately 1.67 m/s².
(b) Time can be calculated using the equation:
s = ut + 0.5at²
Where u is the initial velocity (0 m/s), a is the acceleration (1.67 m/s²), and s is the displacement (120 m).
Plugging in the values, we have:
120 = 0 + 0.5(1.67)t²
Simplifying the equation, we get:
t² = (120)/(0.5 * 1.67)
t = √(120/0.835)
t ≈ 11.23 s
Therefore, it takes approximately 11.23 seconds for the car to travel the length of the ramp.
(c) The distance the traffic travels while the car is moving the length of the ramp can be calculated using the equation:
d = v * t
Where v is the velocity of the traffic (20 m/s) and t is the time taken (11.23 s).
Plugging in the values, we have:
d = 20 * 11.23
Therefore, the traffic travels approximately 224.6 meters while the car is moving the length of the ramp.
Learn more about Acceleration and Time Calculation here:https://brainly.com/question/33447146
#SPJ11
The final answers are [tex](a)~{a ~is~ 1.67 \, \text{m/s}^2} \], ~(b)~{t ~is~ 12s} ~and ~~(c)~d ~is~ 240 \, m[/tex].
To solve the problem, we will use the kinematic equations for uniformly accelerated motion. The car starts from rest, which means its initial velocity (u) is 0 m/s, and it reaches a final velocity (v) of 20 m/s over a distance (s) of 120 m.
a) To find the acceleration (a) of the car, we can use the third kinematic equation that relates initial velocity, final velocity, acceleration, and distance:
[tex]\[ v^2 = u^2 + 2as \]\\ Plugging in the known values, we get: \[ (20 \, \text{m/s})^2 = (0 \, \text{m/s})^2 + 2a(120 \, \text{m}) \] \[ 400 \, \text{m}^2/\text{s}^2 = 240a \, \text{m} \] \[ a = \frac{400 \, \text{m}^2/\text{s}^2}{240 \, \text{m}} \] \[ a = \frac{100}{60} \, \text{m/s}^2 \] \[ a = \frac{5}{3} \, \text{m/s}^2 \] \[ a \approx 1.67 \, \text{m/s}^2 \][/tex]
b) To find the time (t) it takes for the car to travel the length of the ramp, we can use the first kinematic equation:
[tex]\[ v = u + at \]\\ Since the initial velocity (u) is 0 m/s, the equation simplifies to: \[ 20 \, \text{m/s} = 0 + \left(\frac{5}{3} \, \text{m/s}^2\right)t \] \[ t = \frac{20 \, \text{m/s}}{\frac{5}{3} \, \text{m/s}^2} \] \[ t = \frac{20}{1} \cdot \frac{3}{5} \, \text{s} \] \[ t = 12 \, \text{s} \][/tex]
c) While the car is accelerating along the ramp, the traffic on the freeway is moving at a constant speed of 20 m/s. The distance (d) the traffic travels in the time (t) the car takes to travel the ramp is given by:
[tex]\[ d = vt \] \[ d = (20 \, \text{m/s})(12 \, \text{s}) \] \[ d = 240 \, \text{m} \][/tex]
So, the traffic on the freeway travels 240 meters while the car is moving the length of the ramp.
The final answers are:
[tex]\[ \boxed{a \approx 1.67 \, \text{m/s}^2} \] \[ \boxed{t = 12 \, \text{s}} \] \[ \boxed{d = 240 \, \text{m}} \][/tex]
A block is given a short push and then slides with constant friction across a horizontal floor. Which statement best explains the direction of the force that friction applies on the moving block?a. Friction will be in the same direction as the block's motion because molecular interactions between the block and the floor will deform the block in the direction of motion.
b. Friction will be in the same direction as the block's motion because thermal energy generated at the interface between the block and the floor adds kinetic energy to the block.
c. Friction will be in the opposite direction of the block's motion because molecular interactions between the block and the floor will deform the block in the opposite direction of motion.
d. Friction will be in the opposite direction of the block's motion because thermal energy generated at the interface between the block and the floor converts some of the block's kinetic energy to potential energy.
Answer:
c. Friction will be in the opposite direction of the block's motion because molecular interactions between the block and the floor will deform the block in the opposite direction of motion.
Explanation:
When a block is put on the floor , there is interaction at molecular level between the molecules of block and floor . This mutual interaction
( attraction ) pulls them together. When the body is pushed forward, the distance between molecules is increased . Due to mutual attraction , block is deformed at the interface in the opposite direction of motion . This strain causes restoring stress which is also called friction . This elastic stress creates force on the block in backward direction and force on the floor in forward direction .
Final answer:
The correct statement is C. Friction acts in the opposite direction of the block's motion due to molecular interactions between the block and the floor, and it always opposes the motion to slow down or stop the block.
Explanation:
The correct answer to the question, "Which statement best explains the direction of the force that friction applies on the moving block is that friction will be in the opposite direction of the block's motion. This occurs because friction always opposes the direction of motion to prevent or slow down the motion of the block. The encounter between the block and the floor's surface creates molecular interactions that resist the block's movement, and thus, the force of friction acts in the opposite direction to the motion of the block.
Moreover, it's essential to clarify that while friction does generate thermal energy due to the interactions at the interface between the block and the floor, this thermal energy does not add kinetic energy to the block or convert kinetic energy into potential energy in the context of motion. Instead, it's a byproduct of the frictional force's work against the block's motion.
The following position-dependent net force acts on a 3 kg block:
[F subscript n e t end subscript open parentheses x close parentheses equals open parentheses 3 straight N over straight m squared close parentheses x squared]If the block starts at rest at x = 2 m, what is the magnitude of its linear momentum (in kgm/s) at x = 4 m?
Answer:
Explanation:
Given
F_net(x) = (3 x²) N
m v dv / dt = 3 x²
m v dv = 3 x² dx
integrating on both sides and taking limit from x = 2 to 4 m
m v² / 2 - 0 = 3 x³ / 3
mv² / 2 = 4³ - 2³
mv² / 2 = 64 - 8
3 x v² /2 = 56
v = 6.11 m / s
linear momentum
= m v
= 3 x 6.11
= 18.33 kgm/s
Answer:
[tex]p=m.v=37\ kg.m.s^{-1}[/tex]
Explanation:
Given:
[tex]F_{net}=3x^2\ [N][/tex]The initial position of the block, [tex]x=2\ m[/tex]mass of the block, [tex]m=3\ kg[/tex]final position of the block, [tex]x=4\ m[/tex]WE know from the Newton's second law:
[tex]\frac{d}{dt} (p)=F[/tex]
where:
[tex]p=[/tex] momentum
[tex]F=[/tex] force
[tex]t=[/tex] times
Now put the values
[tex]\frac{d}{dt} (mv)=3\cdot x^2[/tex]
[tex]m.\frac{d}{dt} (v)=4\times x^2[/tex]
Now integrate both sides from final limit to initial:
[tex]m.v=\int\limits^4_2 {3x^2} \, dx[/tex]
[tex]m.v=[\frac{3x^3}{3} ]^4_2[/tex]
[tex]m.v=4^3-2^3[/tex]
[tex]p=m.v=56\ kg.m.s^{-1}[/tex]
Solve for (b) how many revolutions it takes for the cd to reach its maximum angular velocity in 1.36s?
Angular displacement of the cd is 3.25 rev
Explanation:
The question is incomplete. It is not given what is the maximum angular velocity of the cd.
Here we are going to assume that the maximum angular velocity is:
[tex]\omega = 30 rad/s[/tex]
The motion of the cd is an accelerated angular motion, therefore we can use the following suvat equation:
[tex]\theta = (\frac{\omega_0 + \omega}{2})t[/tex]
where:
[tex]\theta[/tex] is the angular displacement of the cd during the time interval t
[tex]\omega_0[/tex] is the initial angular velocity of the cd
[tex]\omega[/tex] is the final angular velocity
Here we have:
t = 1.36 s
[tex]\omega_0 = 0[/tex] (assuming the cd starts from rest)
Therefore, the angular displacement of the cd during this time is:
[tex]\theta=(\frac{0+30}{2})(1.36)=20.4 rad[/tex]
And since [tex]1 rev = 2 \pi rad[/tex], we can convert into number of revolutions completed:
[tex]\theta = 20.4 rad \cdot \frac{1}{2\pi rad/rev}=3.25 rev[/tex]
Learn more about angular motion:
brainly.com/question/9575487
brainly.com/question/9329700
brainly.com/question/2506028
#LearnwithBrainly
The blackbody curve of a star moving toward Earth would have its peak shifted (a) to lower intensity; (b) toward higher energies; (c) toward longer wavelengths; (d) toward lower energies.
As show the figure, peak of each blackbody curves shifts towards higher frequency. Then energy emitted by the black body is directly proportional to the frequency incident radiation.
Hence peak is shifted to higher energies.
Therefore the correct option is B: Toward higher energies.
The blackbody curve of a star moving towards Earth would see its peak shifted toward higher energies due to the Doppler Effect, creating a 'blue shift' in the light we observe.
Explanation:The blackbody curve of a star moving toward Earth undergoes a phenomenon known as the Doppler Effect. When a star moves towards the observer, this effect causes the light from that star to be blue-shifted, which means the light moves towards higher energies, or shorter wavelengths. Therefore, the correct answer is (b) - the peak of the blackbody curve shifts towards higher energies.
Learn more about Doppler Effect here:
https://brainly.com/question/33454469
#SPJ3
A roller coaster car drops a maximum vertical distance of 35.4 m. Part A Determine the maximum speed of the car at the bottom of that drop. Ignore work done by friction. Express your answer with the appropriate units.
Answer:
Explanation:
Maximum vertical distance or height = h = 35.4 m
let's consider the initial speed at the top is zero.
As the roller coaster is coming from top to bottom there is the conversion of gravitational potential energy into kinetic energy. So we will consider the law of conservation of energy.
As in this case,
Loss in potential energy = Gain in Kinetic energy
mgh = 1/2mv²
mass will cancel out will mass.
gh = 1/2 v²
v = √2gh
v = √2×9.8×35.4
v =√693.84
v = 26.34 m/s
The rollar coaster will have the maximum speed of 26.34 m/s when it reaches the bottom if we ignore the frictional forces.
Answer:
26.34 m/s.
Explanation:
Given:
h = 5.4 m
g = 9.81 m/s^2
Change in Potential energy = change in Kinetic energy
mgh = 1/2mv²
gh = 1/2 v²
v = √2gh
= √2×9.8×35.4
=√693.84
v = 26.34 m/s.
An electron (mass = 9.11 X 10^-31 kg) leaves one end of a TV picture tube with zero initial speed and travels in a straight line to the accelerating grid, which is 1.80 cm away. It reaches the grid with a speed of 3.00 X 10^6 m/s. If the accelerating force is constant, compute (a) the acceleration(b) the time to reach the grid(c) the net force, in newtons. (You can ignore the gravitational force on the electron.)
Answer: a) 2.5 * 10^14, b) t = 1.2*10^-8 s, c) F = 2.2775 * 10^-15 N
Explanation: Since it starts from rest, initial velocity = 0, final velocity (v) = 3*10^6 m/s, distance covered (s) = 1.80cm = 1.80/100 = 0.018m
Since the force on the electron is constant, it acceleration will be constant too thus making newton's laws of motion valid.
Question a)
To get the acceleration, we use the formulae that
v² = u² + 2as
But u = 0
v² = 2as
(3*10^6)² = 2*a*(0.018)
9* 10^12 = 0.036*a
a = 9 * 10^12 / 0.036
a = 250 * 10^12
a = 2.5 * 10^14 m/s².
Question b)
To get the time, we use
v = u + at
But u = 0
v = at
3*10^6 = 2.5 * 10^14 * t
t = 3*10^6 / 2.5*10^14
t = 1.2*10^-8 s
Question c)
To get the force, we use the formulae below
F = ma
F = 9.11*10^-31 * 2.5 * 10^14
F = 22.775 * 10^-17
F = 2.2775 * 10^-15 N
a) The acceleration of the electron as it travels in a straight line to the grid is 2.5 × 10¹⁴m/s².
b) The time taken for the electron to reach the grid is 1.2 × 10⁻⁸ seconds.
c) The net force that is accelerating the electron is 2.28 × 10⁻¹⁶ Newton.
Given the data in the question
Mass of electron; [tex]m = 9.11 * 10^{31} kg[/tex]Initial velocity; [tex]u = 0[/tex]'Final velocity; [tex]v = 3.00*10^6 m/s[/tex]Distance traveled; [tex]s = 1.80cm = 0.018m[/tex]Acceleration; [tex]a = \ ?[/tex]
Time taken; [tex]t = \ ?[/tex]
Net force; [tex]F = \ ?[/tex]
a)
To determine the acceleration of the electron, we use the third equation of motion:
[tex]v^2 = u^2 + 2as[/tex]
Where v is the final velocity, u is the initial velocity, a is the acceleration and s is the distance traveled.
We substitute our given values into the equation
[tex](3.00 *10^6 m/s)^2 = 0^2 + [ 2 * a * 0.018m ]\\\\9.0 *10^{12} m^2/s^2 = a * 0.036m\\\\a = \frac{9.0 *10^{12} m^2/s^2}{0.036m} \\\\a = 2.5 * 10^{14}m/s^2[/tex]
Therefore, the acceleration of the electron as it travels in a straight line to the grid is 2.5 × 10¹⁴m/s².
b)
To the the time taken to reach the grid, we use the first equation of motion:
[tex]v = u + at[/tex]
Where v is the final velocity, u is initial velocity, a is the acceleration and t is the time taken
We substitute our values into the equation
[tex]3.00 * 10^6 m/s = 0 + [ ( 2.5*10^{14}m/s^2) * t\\\\3.00 * 10^6 m/s = ( 2.5*10^{14}m/s^2) * t\\\\t = \frac{3.00 * 10^6 m/s}{2.5*10^{14}m/s^2} \\\\t = 1.2 * 10^{-8}s[/tex]
Therefore, time taken for the electron to reach the grid is 1.2 × 10⁻⁸ seconds.
c)
To determine the net force of the electron, we use the expression from newton second law of motion:
[tex]F = m * a[/tex]
Where m is mass and a is the acceleration
We substitute our values into the equation
[tex]F = ( 9.11 * 10^{-31} kg ) * ( 2.5 * 10^{14}m/s^2)\\\\F = 2.28 * 10^{-16} kg.m/s^2\\\\F = 2.28 * 10^{-16}N[/tex]
Therefore, the net force that is accelerating the electron is 2.28 × 10⁻¹⁶ Newton.
Learn more: https://brainly.com/question/16968602
If it takes about 8 minutes for light to travel from the Sun to Earth, and Pluto is 40 times this distance from us, how long does it take light to reach Earth from Pluto?
Light takes 320 minutes to reach Earth from Pluto
Explanation:
We can solve this problem by applying the rule of three. We can do as follows:
- We call [tex]x[/tex] the distance between the Sun and the Earth
- Then the distance between the Earth and Pluto is 40 times this distance, so [tex]40x[/tex]
- Light takes about 8 minutes to cover the distance x between Sun and Earth
Therefore, calling T the time that light takes to cover distance between Earth and Pluto (40x), we can write:
[tex]\frac{x}{8}=\frac{40x}{T}[/tex]
And solving for T,
[tex]T=\frac{8\cdot 40 x}{x}=320 min[/tex]
Learn more about distance:
brainly.com/question/3969582
#LearnwithBrainly
A high-speed K0 meson is traveling at β = 0.90 when it decays into a π + and a π − meson. What are the greatest and least speeds that the mesons may have?
Answer:
greatest speed=0.99c
least speed=0.283c
Explanation:
To solve this problem, we have to go to frame of center of mass.
Total available energy fo π + and π - mesons will be difference in their rest energy:
[tex]E_{0,K_{0} }-2E_{0,\pi } =497Mev-2*139.5Mev\\[/tex]
=218 Mev
now we have to assume that both meson have same kinetic energy so each will have K=109 Mev from following equation for kinetic energy we have,
K=(γ-1)[tex]E_{0,\pi }[/tex]
[tex]K=E_{0,\pi}(\frac{1}{\sqrt{1-\beta ^{2} } } -1)\\\frac{1}\sqrt{1-\beta ^{2} }}=\frac{K}{E_{0,\pi}}+1\\ {1-\beta ^{2}=\frac{1}{(\frac{K}{E_{0,\pi}}+1)^2}}\\\beta ^{2}=1-\frac{1}{(\frac{K}{E_{0,\pi}}+1)^2}}\\\beta = +-\sqrt{\frac{1}{(\frac{K}{E_{0,\pi}}+1)^2}}\\\\\\beta =+-\sqrt{1-\frac{1}{(\frac{109Mev}{139.5Mev+1)^2}}[/tex]
[tex]u'=+-0.283c[/tex]
note +-=±
To find speed least and greatest speed of meson we would use relativistic velocity addition equations:
[tex]u=\frac{u'+v}{1+\frac{v}{c^{2} } } u'\\u_{max} =\frac{u'_{+} +v_{} }{1+\frac{v}{c^{2} } } u'_{+} \\u_{max} =\frac{0.828c +0.9c }{1+\frac{0.9c}{c^{2} } } 0.828\\ u_{max} =0.99c\\u_{min} =\frac{u'_{-} +v_{} }{1+\frac{v}{c^{2} } } u'_{-}\\u_{min} =\frac{-0.828c +0.9c }{1+\frac{0.9c}{c^{2} } } -0.828c\\u_{min} =0.283c[/tex]
Final answer:
The greatest and least speeds of the π mesons resulting from the decay of a high-speed K0 meson are calculated using the relativistic laws of velocity addition. The maximum speed is (85/86)c, and the minimum speed is (5/14)c.
Explanation:
The question revolves around a high-speed K0 meson decaying into two π mesons (π+ and π-). To determine the greatest and least speeds that the π mesons can have, we employ the relativistic addition of velocities. The formula used in this context is Vx=(Vx'+V)/(1+(Vx'V/c²)), where V is the speed of the K0 meson, Vx' the speed of π mesons in the K0 meson's rest frame, and c is the speed of light.
The maximum speed is achieved when the π meson is emitted in the same direction as the K0 meson's movement, while the minimum speed occurs when the π meson is emitted in the opposite direction. Considering the K0 meson's speed (0.9c) and the π mesons' speed in the rest frame (0.8c), the equations result in the maximum speed being (85/86)c and the minimum speed being (5/14)c respectively.
A skydiver jumps out of a plane wearing a suit which provides a deceleration due to air resistance of 0. 45 m/s^2 for each 1 m/s of the skydivers velocity. Set up an initial value problem that models the skydivers velocity (v(t)). Then calculate the skydivers terminal speed assuming that the acceleration due to gravity is 9.8m/s^2 slader.
Explanation:
When the skydiver accelerates in the downward direction then tends to gain speed with each second. More is the resistance in air more will be the increase accompanied by the skydiver.
As a result, a point will come where air resistance force is balanced by gravitational force. Hence, the skydiver will attain terminal velocity.
So, air resistance for 1 [tex]m/s^{2}[/tex] = 0.45 [tex]m/s^{2}[/tex]
Air resistance for v [tex]m/s^{2}[/tex] = 0.45 v[tex]m/s^{2}[/tex]
As acceleration = change in velocity w.r.t time
a = [tex]\frac{dv}{dt}[/tex] = 0.45
[tex]\frac{dv}{V}[/tex] = 0.45t
Now, we will integrate both the sides as follows.
ln V = 0.45t
V = [tex]e^{0.45t}[/tex]
Since, [tex]F_{a} = F_{g}[/tex] (in the given case)
so, ma = mg
On cancelling the common terms the equation will be as follows.
0.45 v = 9.8 [tex]m/s^{2}[/tex]
v = 21.77 [tex]m/s^{2}[/tex]
Thus, we can conclude that the skydivers terminal speed is 21.77 [tex]m/s^{2}[/tex].
A cold soda initially at 2ºC gains 18 kJ of heat in a room at 20ºC during a 15-min period. What is the average rate of heat transfer during this process?
Answer:
q= 20 W
Explanation:
Given that
Initial temperature ,T₁ = 2 ºC
Heat gains ,Q = 18 kJ
The final temperature ,T₂ = 20 ºC
time ,t= 15 min
We know that
1 min = 60 s
t= 15 x 60 = 900 s
The average rate of heat transfer is give as
[tex]q=\dfrac{Q}{t}[/tex]
[tex]q=\dfrac{18}{900}\ kW[/tex]
q=0.02 kW
q= 20 W
Therefore the rate of heat transfer will be 20 W.
A soda is initially at 2 °C and 15 minutes later, after gaining 18 kJ, its temperature is 20 °C. The average rate of heat transfer is 20 W.
What is heat transfer?Heat transfer describes the flow of heat (thermal energy) due to temperature differences and the subsequent temperature distribution and changes.
A soda is initially at 2 °C and 15 minutes later, after gaining 18 kJ, its temperature is 20 °C.
First, we will convert 15 min to seconds using the conversion factor 1 min = 60 s.
15 min × 60 s/1 min = 900 s
Then, we can calculate the average rate of heat transfer using the following expression.
q = Q/t = 18 × 10³ J / 900 s = 20 W
where,
q is the average rate of heat transfer.Q is the heat gained.t is the time elapsed.A soda is initially at 2 °C and 15 minutes later, after gaining 18 kJ, its temperature is 20 °C. The average rate of heat transfer is 20 W.
Learn more about heat transfer here: https://brainly.com/question/16055406
A car’s velocity as a function of time is given by vx(t) = α + βt2, where α = 3.00 m/s and β = 0.100 m/s3. (a) Calculate the average acceleration for the time interval t = 0 to t = 5.00 s. (b) Calculate the instantaneous acceleration for t = 0 and t = 5.00 s. (c) Draw vx-t and ax-t graphs for the car’s motion between t = 0 and t = 5.00 s.
The average acceleration from t=0 to t=5.00 s is 0.5 m/s^2. instantaneous acceleration at t=0 is 0 m/s^2 and at t=5.00 s is 1.0 m/s^2. The velocity-time graph is parabolic, and the acceleration-time graph shows linear growth.
The velocity of a car as a function of time is given by vx(t) = \\(\alpha + \beta t^2\\), where \\(\alpha = 3.00 m/s\\) and \beta = 0.100 m/s^3. To find the average acceleration for the time interval from t = 0 to t = 5.00 s, we need the change in velocity over the time period. Using the given function, we can calculate the initial velocity at t = 0, which is v(0) = 3.00 m/s, and the final velocity at t = 5.00 s, which is v(5) = 3.00 + 0.100(5)^2 = 3.00 + 2.5 = 5.5 m/s. The average acceleration is then (5.5 m/s - 3.0 m/s) / (5.0 s - 0 s) = 0.5 m/s^2.
For instantaneous acceleration at any given time, we differentiate the velocity function with respect to time to obtain a(t) = dvx/dt = 2\beta t. Therefore, the instantaneous acceleration at t = 0 is a(0) = 2(0.100)(0) = 0 m/s^2, and at t = 5.00 s is a(5) = 2(0.100)(5) = 1.0 m/s^2.
When drawing the vx-t and ax-t graphs, for the velocity-time graph, the curve will start at 3.00 m/s and rise parabolically due to the \(t^2\) term in the function. For the acceleration-time graph, the line will start at 0 m/s^2 and increase linearly with time, passing through 1.0 m/s^2 at 5 seconds.
After a great many contacts with the charged ball, how is any charge on the rod arranged (when the charged ball is far away)?There is positive charge on end B and negative charge on end A.There is negative charge spread evenly on both ends.There is negative charge on end A with end B remaining neutral.There is positive charge on end A with end B remaining neutral.The conducting rod is not grounded, so a negative charge accumulates on one end, but a charge cannot remain at a single end in a conductor, so it will spread to both ends:There is negative charge spread evenly on both ends
Answer:
The correct option is that both the ends will remain neutral.
Explanation:
As the rod is grounded all of the prolonged charge will be converted to ground so the overall charge on the rod in absence of the charged ball will be equal to zero.Such that the both ends will not bear any charge.
The correct option is: There is negative charge spread evenly on both ends.
When a conducting rod is brought into contact with a charged ball, charge transfer occurs due to the process of induction and conduction. Initially, when the charged ball (let's assume it is positively charged) is brought close to the rod, it will induce a negative charge on the end of the rod nearest to the ball (end A) and a positive charge on the far end (end B) due to the separation of charges within the conductor. This is because the positive charge on the ball will repel the positive charges within the rod, pushing them away, and attract the negative charges, pulling them towards the ball.
Once the rod is actually touched to the ball, the negative charges on the rod (which were induced by the ball's positive charge) will be neutralized by the positive charges from the ball, leaving the rod with a net negative charge after the ball is moved away. This negative charge will be evenly distributed along the rod initially.
However, since the rod is not grounded, the negative charge will not have a path to escape and will remain on the rod. Due to the repulsion between like charges (negative-negative), these charges will repel each other and spread out as far as possible from each other along the length of the rod. This means that the negative charge will be spread evenly on both ends of the rod, as this arrangement minimizes the repulsive forces between the charges and results in the lowest potential energy configuration.
Therefore, the final arrangement of any charge on the rod, when the charged ball is far away, will be an even distribution of negative charge on both ends A and B of the rod. This is consistent with the principle of electrostatic equilibrium, where charges within a conductor will redistribute themselves to minimize repulsion and achieve the lowest energy state.
Coulomb's law for the magnitude of the force FFF between two particles with charges QQQ and Q′Q′Q^\prime separated by a distance ddd is |F|=K|QQ′|d2|F|=K|QQ′|d2, where K=14πϵ0K=14πϵ0, and ϵ0=8.854×10−12C2/(N⋅m2)ϵ0=8.854×10−12C2/(N⋅m2) is the permittivity of free space. Consider two point charges located on the x axis: one charge, q1q1q_1 = -13.5 nCnC , is located at x1x1x_1 = -1.735 mm ; the second charge, q2q2q_2 = 35.5 nCnC , is at the origin (x=0.0000)
The force between the two charges, according to Coulomb's law, is approximately 1.92 Newtons. Note that the force is attractive since one charge is positive and the other is negative.
Explanation:The question refers to Coulomb's law, which is fundamental in Physics. The law describes the force between two electric charges. We apply the formula |F|=K|QQ′|/d^2 where the charges are Q1=-13.5nC (converted to C by multiplying by 10^-9) and Q2=35.5nC, the distance d=1.735mm (converted to meters by multiplying by 10^-3), and K=1/4πϵ0≈8.99x10^9 N.m²/C². Inserting these values into the formula we get |F| ≈ 1.92 N. The magnitude of the force is therefore approximately 1.92 Newtons. It's important to note that since one charge is positive and the other negative, the force will be attractive, not repulsive.
Learn more about Coulomb's Law here:https://brainly.com/question/32002600
#SPJ3
A ball is dropped from the top of a building when does the ball have the most potential energy? A halfway through the fall B just before it hits the ground C after it has hit the ground D before it is released
Answer:
As potential energy depends on height
P.E=mgh
m and g remains same
just before release it has maximum height,thus option D it has maximum potential energy.
The ball has the most potential energy when it is at the top of the building D. before it is released.
Explanation:Potential energy is stored energy that an object possesses due to its position, state, or condition. It can be gravitational, elastic, chemical, or electrical. The energy is converted to kinetic energy when the object moves or undergoes a change in its physical or chemical state.
The ball has the most potential energy when it is at the top of the building before it is released. Potential energy depends on an object's height and mass. When the ball is at the top of the building, it has the maximum height and therefore the most potential energy. As the ball falls, its potential energy decreases and is converted into kinetic energy.
Here we'll see that an emf can be induced by the motion of the conductor in a static magnetic field. The U-shaped conductor in (Figure 1) lies perpendicular to a uniform magnetic field B⃗ with magnitude B=0.75T , directed into the page. We lay a metal rod with length L=0.10m across the two arms of the conductor, forming a conducting loop, and move the rod to the right with constant speed v=2.5m/s . What is the magnitude of the resulting emf?
With the given magnetic field and rod length, what must the speed be if the induced emf has magnitude 0.73 V ?
Answer:
a) ΔV = 0.1875 V , b) v = 9.73 m / s
Explanation:
For this exercise we can use Necton's second law, as the speed is constant the forces on the driver are equal
[tex]F_{E} - F_{B}[/tex] = 0
[tex]F_{E}[/tex] = F_{B}
q E = q v B
E = v B
The electrical force induced in the conductor is
ΔV = E l
ΔV = v B l
Let's calculate
ΔV = 2.5 0.75 0.10
ΔV = 0.1875 V
b) If ΔV = 0.73 what speed should it have
v = DV / B l
v = 0.73 / 0.75 0.1
v = 9.73 m / s
An electron moves to a higher energy level in an atom after absorbing a photon of a specific energy. (T/F)
Answer:
T
Explanation:
I learned this in 5th grade
It is true that an electron moves to a higher energy level in an atom after absorbing a photon of a specific energy.
What is electron excitation?The transfer of a bound electron to a more energetic, but still bound, state is known as electron excitation.
This can be accomplished through photoexcitation, in which the electron absorbs a photon and absorbs all of its energy, or through electrical excitation, in which the electron receives energy from another, more energetic electron.
An electron can become excited if it receives additional energy, such as when it absorbs a photon, or light packet, or collides with a nearby atom or particle.
Electrons can absorb energy (discretely) to move from lower to higher energy states.
When they reach higher energy states, they become unstable and emit photons to return to their ground state (of specific energy).
Thus, the given statement is true.
For more details regarding electrons, visit:
https://brainly.com/question/1255220
#SPJ2
Can you have zero displacement and nonzero average velocity? Zero displacement and nonzero velocity? Illustrate your answers on an x-t graph.
a) Not possible
b) Yes, it's possible (see graph in attachment)
Explanation:
a)
The average velocity of a body is defined as the ratio between the displacement and the time elapsed:
[tex]v=\frac{\Delta x}{\Delta t}[/tex]
where
[tex]\Delta x[/tex] is the displacement
[tex]\Delta t[/tex] is the time elapsed
In this problem, we want to have zero displacement and non-zero average velocity. From the equation above, we see that this is not possible. In fact, if the total displacement is zero,
[tex]\Delta x = 0[/tex]
And therefore as a consequence,
[tex]v=0[/tex]
which means that the average velocity is zero.
B)
Here we want to have zero displacement and non-zero velocity. In this case, it is possible: in fact, we are not talking about average velocity, but we are talking about (instantaneous) velocity.
On a position-time graph, the instantaneous velocity is the slope of the graph. Look at the graph in attachment. We see that the position of the object first increases towards positive value, then it decreases (the object starts moving backward), then becomes negative, then it increases again until returning to the original position, x = 0.
In all of this, we notice that the total displacement of the object is zero:
[tex]\Delta x = 0[/tex]
However, we notice that the instantaneous velocity of the object at the various instants is not zero, because the slope of the graph is not zero.
Learn more about average velocity:
brainly.com/question/8893949
brainly.com/question/5063905
#LearnwithBrainly
Zero displacement and nonzero average velocity can occur on an x-t graph, but it is not possible to have zero displacement and nonzero velocity simultaneously.
Explanation:Zero displacement and nonzero average velocity can occur when an object moves back and forth over a certain distance and returns to its original position, but with a change in time. For example, if you consider a person running in a circular track, after each lap the person returns to the starting point, resulting in zero displacement. However, if the person completes the laps in different time intervals, their average velocity will be nonzero.
On the other hand, it is not possible to have zero displacement and nonzero velocity simultaneously. Velocity is defined as the rate of change of displacement with respect to time. If the displacement is zero, then the velocity must also be zero
In an x-t graph, zero displacement would be represented by the horizontal line at the x-axis, or the line parallel to the x-axis. Nonzero average velocity would be represented by a sloped line that is above or below the x-axis, indicating movement in either the positive or negative direction.
Learn more about Displacement and Velocity here:https://brainly.com/question/37832018
#SPJ6
Two loudspeakers are placed next to each other and driven by the same source at 500 Hz. A listener is positioned in front of the two speakers and on the line separating them, thus creating a constructive interference at the listener's ear. What minimum distance would one of the speakers be moved back away from the listener to produce destructive interference at the listener's ear? (The speed of sound = 340 m/s.)
To solve this problem we will apply the concepts related to wavelength as the rate of change of the speed of the wave over the frequency. Mathematically this is
[tex]\lambda = \frac{v}{f}[/tex]
Here,
v = Wave velocity
f = Frequency,
Replacing with our values we have that,
[tex]\lambda = \frac{340}{500}[/tex]
\lambda = 0.68m
The distance to move one speaker is half this
[tex]\lambda/2 = 0.34m[/tex]
Therefore the minimum distance will be 0.34m
The minimum distance that one of the speakers should be moved back away from the listener to produce destructive interference at the listener's ear is; Δ = 0.34 m
The formula for wavelength here as it relates to speed and frequency is given as;
λ = v/f
Where;
λ is wavelength
v is speed
f is frequency
We are given;
Frequency; f = 500 Hz
Speed of sound; v = 340 m/s
Thus;
λ = 340/500
λ = 0.68 m
Now, we are told that the line separating them creates a constructive interference at the listeners ear. Thus;
To calculate the minimum distance would one of the speakers be moved back away from the listener to produce destructive interference at the listener's ear we will use the formula;
formula for destructive path length is;
Δ = (m + ½)λ
And m here is zero
Thus;
Δ = ½λ
Δ = 0.68/2
Δ = 0.34 m
Read more at; https://brainly.com/question/14718577
How did the temperature structure of the solar nebula determine planetary composition?
Explanation:
The temperature of the solar nebula was decreasing as it moved away from its center. Therefore, only heavy elements could condense in the inner solar system and terrestrial planets could not form with light elements, such as gases. In the outer solar system, the Jovian planets formed mostly with gases, since temperatures were too low to allow rocky compositions.
If the vector components of the position of a particle moving in the xy plane as a function of time are x = (2.7 m/s2)t2i and y = (5.1 m/s3)t3j, at what time t is the angle between the particle's velocity and the x axis equal to 45°?
Answer:
Time: 0.35 s
Explanation:
The position vector of the particle is
[tex]r=(2.7m/s^2)t^2 i+(5.1 m/s^3)t^3j[/tex]
where the first term is the x-component and the 2nd term is the y-component.
The particle's velocity vector is given by the derivative of the position vector, so:
[tex]v=r'(t)=(2.7\cdot 2)t i + (5.1\cdot 3)t^2 j=5.4t i+15.3t^2j[/tex]
The particle's velocity has an angle with the x-axis of 45 degrees when the x and the y component have same magnitude. Therefore:
[tex]5.4t=15.3t^2\\5.4=15.3t\\t=\frac{5.4}{15.3}=0.35 s[/tex]
The time t at which the angle between the particle's velocity and the x-axis is 45°, given the vectors x = (2.7 m/s^2)t^2 i and y = (5.1 m/s^3)t^3 j, is found to be 0.35 seconds.
Explanation:To solve this problem, first we need to find the velocity of the particle in both the x and y directions. The velocity in the x-direction, vx, is just the derivative of x with respect to time, dx/dt = (2.7 m/s2)(2t) = 5.4t m/s. The velocity in the y-direction, vy, is the derivative of y with respect to time, dy/dt = (5.1 m/s3)(3t2) = 15.3t2 m/s.
Now, the angle θ between the velocity and the x-axis can be found by taking the tangent inverse of the ratio of vy to vx: θ = tan-1(vy/vx). We want this angle to be 45°, so we set this equation equal to 45° and solve for t. θ = 45° = tan-1((15.3t2 m/s) / (5.4t m/s)) => tan(45) = 15.3t2 / 5.4t => 1 = 15.3t / 5.4 => t = 5.4 / 15.3 s= 0.35s.
Learn more about vector components here:https://brainly.com/question/31400182
#SPJ3
What magnitude point charge creates a 10,000 N/C electric field at a distance of 0.250 m? (b) How large is the field at 10.0 m?
Answer:
(a) 69.52 x 10⁻⁹ C
(b) 6.25 N/C
Explanation:
(a) The electric field (E) due to a point charge is directly proportional to the magnitude of the point charge (Q) and inversely proportional to the square of the distance (r) between the point charge and the point where the electric field is. This can be represented as follows;
E = k Q / r² ---------------------------(i)
Where;
k = constant of proportionality called electric constant = 8.99 x 10⁹Nm²/C²
From the question, the following are given;
E = 10000N/C
r = 0.250m
Substitute these values into equation (i) as follows;
=> 10000 = 8.99 x 10⁹ x Q / 0.250²
=> 10000 = 8.99 x 10⁹ x Q / 0.0625
=> 10000 = 143.84 x 10⁹ x Q
Solve for Q;
Q = 10000 / (143.84 x 10⁹)
Q = 69.52 x 10⁻⁹ C
Therefore, the magnitude of the point charge is 69.52 x 10⁻⁹ C.
(b) By the same token, to calculate the magnitude of the electric field at 10.0m, substitute the values of Q = 69.52 x 10⁻⁹ C, k = 8.99 x 10⁹ and r = 10.0m into equation (i) as follows;
=> E = 8.99 x 10⁹ x 69.52 x 10⁻⁹ / 10.0²
=> E = 8.99 x 69.52 / 100.0
=> E = 6.25 N/C
Therefore, the electric field at 10.0m is as large as 6.25 N/C
Consider two identical and symmetrical wave pulses on a string. Suppose the first pulse reaches the fixed end of the string and is reflected back and then meets the second pulse. When the two pulses overlap exactly, the superposition principle predicts that the amplitude of the resultant pulses, at that moment, will be what factor times the amplitude of one of the original pulses?a. 0b. 1c. -2d. -1
Answer:
The amplitude of the resultant wave will be 0.
Explanation:
Suppose the first wave has an amplitude of A. Its angle is given as wt.
The second way will also have the same amplitude as that of first.
After the reflection, a phase shift of π is added So the wave is given as
[tex]W_1=W_2=Acos(\omega t)\\W_1^{'}=Acos(\omega t+ \pi)[/tex]
Adding the two waves give
[tex]W_1'+W_2=Acos(\omega t+ \pi)+Acos(\omega t)\\W_1'+W_2=-Acos(\omega t)+Acos(\omega t)\\W_1'+W_2=0[/tex]
So the amplitude of the resultant wave will be 0.
A particle executes simple harmonic motion with an amplitude of 3.00 cm. At what position does its speed equal half of is maximum speed?
The speed equals half of its maximum speed at positions ±1.50 cm from the equilibrium for an amplitude of 3.00 cm.
Speed equals half of its maximum speed when the particle is at a position where it is halfway through its amplitude.
This occurs at x = ±0.5X from the equilibrium position, considering X as the amplitude of the motion.
For an amplitude of 3.00 cm, the speed equals half of its maximum speed at position ±1.50 cm.
An 1,840 W toaster, a 1,460 W electric frying pan, and a 50 W lamp are plugged into the same outlet in a 15 A, 120 V circuit. (The three devices are in parallel when plugged into the same socket.) (a) What current (in A) is drawn by each device?
Answer:
Explanation:
Given
Power drawn by toaster [tex]P_1=1840\ W[/tex]
Power drawn by Electric fan [tex]P_2=1460\ W[/tex]
Power drawn by lamp [tex]P_3=50\ W[/tex]
Voltage applied [tex]V=120\ V[/tex]
If appliances are applied in parallel then Voltage applied is same
Power is given by [tex]P=\frac{V^2}{R}[/tex]
Resistance of toaster [tex]R_1=\frac{120^2}{1840}=7.82\ \Omega [/tex]
Resistance of electric Fan [tex]R_2=\frac{120^2}{1460}=9.86\ \Omega [/tex]
Resistance of toaster [tex]R_3=\frac{120^2}{50}=288\ \Omega [/tex]
Current is given by
[tex]I=\frac{V}{R}[/tex]
[tex]I_1=\frac{120}{7.82}=15.34\ A[/tex]
[tex]I_2=\frac{120}{9.86}=12.17\ A[/tex]
[tex]I_3=\frac{120}{288}=0.416\ A[/tex]
Answer:
Explanation:
power of toaster, P1 = 1840 W
Power of electric frying pan, P2 = 1460 W
Power of lamp, P3 = 50 W
As they all are connected in parallel, so the voltage is same for all.
Let the current in toaster is i1.
P1 = V x i1
1840 = 120 x i1
i1 = 15.33 A
Let the current in frying pan is i2.
P2 = V x i2
1460 = 120 x i1
i1 = 12.17 A
Let the current in lamp is i3.
P3 = V x i3
50 = 120 x i3
i3 = 0.42 A
what is the voltage in mv across an 5.5 nm thick membrane if the electric field strength across it is 5.75 mv/m? you may assume a uniform electric field.
Answer:
V = 31.62 m V
Explanation:
Given,
Voltage across thick membrane = ?
Thickness of the membrane, d = 5.5 n m
Electric field = 5.75 M V/m
we know
[tex]E = \dfrac{V}{d}[/tex]
V = E d
V = 5.75 x 10⁶ x 5.5 x 10⁻⁹
V = 31.62 x 10⁻³ V
V = 31.62 m V
Hence, The Voltage across the membrane is equal to 31.62 m V.
The voltage across the membrane is dependent on the electric field and thickness of the membrane. The voltage across the membrane is 0.0316 V.
What is the voltage?The voltage is defined as the difference in electric potential between two points.
Given that the electric field E is 5.75 mv/m and the thickness of the membrane d is 5.5 nm.
The voltage across the membrane is calculated as given below.
[tex]E = \dfrac {V}{d}[/tex]
[tex]V = Ed[/tex]
[tex]V = 5.75 \times 10^6 \times 5.5 \times 10^{-9}[/tex]
[tex]V = 0.0316 \;\rm V[/tex]
Hence we can conclude that the voltage across the membrane is 0.0316 V.
To know more about the voltage, follow the link given below.
https://brainly.com/question/2364325.
How strong an electric field is needed to accelerate electrons in an X-ray tube from rest to one-tenth the speed of light in a distance of 5.1 cm?
Answer:
E= 50.1*10³ N/C
Explanation:
Assuming no other forces acting on the electron, if the acceleration is constant, we can use the following kinematic equation in order to find the magnitude of the acceleration:
[tex]vf^{2} -vo^{2} = 2*a*x[/tex]
We know that v₀ = 0 (it starts from rest), that vf = 0.1*c, and that x = 0.051 m, so we can solve for a, as follows:
[tex]a = \frac{vf^{2}}{2*x} = \frac{(3e7 m/s)^{2} }{2*0.051m} =8.8e15 m/s2[/tex]
According to Newton's 2nd Law, this acceleration must be produced by a net force, acting on the electron.
Assuming no other forces present, this force must be due to the electric field, and by definition of electric field, is as follows:
F = q*E (1)
In this case, q=e= 1.6*10⁻19 C
But this force, can be expressed in this way, according Newton's 2nd Law:
F = m*a (2) ,
where m= me = 9.1*10⁻³¹ kg, and a = 8.8*10¹⁵ m/s², as we have just found out.
From (1) and (2), we can solve for E, as follows:
[tex]E=\frac{me*a}{e} =\frac{(9.1e-31 kg)*(8.8e15m/s2)}{1.6e-19C} = 50.1e3 N/C[/tex]
⇒ E = 50.1*10³ N/C